OEM spare parts for your VW G60

Close filters
from to
1 From 2
G60 Vent Hose Valve Cover G60 Vent Hose Valve Cover
G60 vent hose valve cover Original VW part number: 037103493L Important: Fits only to chassis number 50-K-030 000
29.95€ *
Kurzer Ölfilter BAR-TEK® Short Oilfilter BAR-TEK®
This short Oilfilter will be needed after installation of an Oilcooler-Kit. With new O-ring. height: 95mm diameter: 75mm MANN or Mahle quality made in germany! We also recommend to use our oil filter cutter to see any problems inside the...
9.95€ *
G60/G40 CO Potentiometer BAR-TEK® G60/G40 CO sensor BAR-TEK®
New CO sensor for all G40 and G60 engines. This sesnor needs a proper calibration for the correct fuel mixture.
249.95€ *
Temperaturfühler Wasser blau Water Temp. Sensor blue
New Watertemperature sensor for all G60, G40, 16V or VR6 Models. This sensor measures the water coolent temp. and fails very often. 2 pole.
16.95€ *
G60 Kabelbaum für Eispritzdüsen BAR-TEK® G60 Cable set for Injectors BAR-TEK®
This cable set is failing very often due to the heat of the engine. The most cracks occure near the injector itself. Broken cables can make malfunction of the injectors and engine can run too lean and fail in the end! We build a new and...
119.95€ *
G60 Stehbolzen Zylinderkopf G60 stud bolt for Cylinderhead
M8 stud bolt for all G60 Cylinderheads with copper Nut. This studs are failing very often during dismounting of the exhaust manifold. (Stud is mounted in the head) Price only for one stud together with copper nut as shown on picture. Per...
3.95€ *
Zylinderkopfschrauben G40/G60 Cylinderhead bolts G40/G60
New headbolts for G-40 or G-60 engines. Specialy for Turbo and Supercharged engines! Tightening torque: 40NM 60NM 2x90° German high quality parts!
49.95€ *
G60 & G40 Unterdruckleitung für Steuergerät GATES G60 & G40 boost hose for ECU GATES
New boost hose for the ECU suitable for all G40 and G60 engines including zink plated clamps. This hose is getting worn and hard after some years and can create leaks so that the ECU is getting wrong signals about the pressure in the...
14.95€ *
G60 6PK Riemen KURZ BAR-TEK® G60 Shorter belt 6PK BAR-TEK®
Shorter belt for smaller pullies. Putting a smaller pully you have to shorten the belt to keep preload on your charger! Up to 65mm pullies or bigger. For all G60 without AC.
29.95€ *
G60 Ventildeckeldichtung G60 camcover gasket
Rubber gasket for camcover for all G60 engines Can be reused. Made in Germany! Fits all G60 engines as used in Golf MK2, Corrado and Passat 35i.
14.95€ *
G60 6PK Riemen Standard G60 belt 6PK standard
Belt for standard pullies on your charger Keeps preload on your charger! For all G60 without AC.
26.95€ *
Kraftstofffilter MANN Fuel filter MANN
High performance fuel filter for nearly each modell. Fuel filters should be replaced after a certian time. The can get stuck and the engine power will be less. Please specify exact car and engine.
19.95€ *
G60 Luftfilter Einsatz G60 Airfilter standard
OEM Airfilter for all G60. Best Filter for your G-Lader!
17.95€ *
G60 Metall Zylinderkopfdichtung G60 Metal Cylinderheadgasket
Finally a high quality metall gasket at an affordable price! This is a great addition to any G60 engine running high boost. Note: -higher boost and HP -Retains factory compression ratio -Two different thicknesses available: 1,6mm or...
From 79.95€ *
G60 Wasserpumpe BAR-TEK® G60 Waterpump BAR-TEK®
High performance waterpump for all G60 models. Complete pump with 2 O-rings. Quality Made in germany.
79.95€ *
G60 Ölpumpe BAR-TEK® G60 Oilpump BAR-TEK®
High quality oilpump for all G60 models. The oil pump is one of the most important parts in an engine! It should be replaced after a certain mileage to maintain enough oil flow and oil pressure in the complete engine system. Once an...
159.95€ *
G60 Zahnriemen mit Spannrolle G60 timing belt with tensiator
High quality OEM GATES belt with tensiator for all G60 engines. Belt from GATES and tensioner from INA. Made in Germany! (Pic shows 16V belt kit. No washer, nut and stud included)
59.95€ *
G60 Zylinderkopf Dichtsatz G60 Cylinderhead gasket-kit
High quality gasket and sealing kit for G60 cylinderhead from high quality. All parts you need for a complete rebuild of your head. Including metal headgasket! Made in Germany.
189.95€ *
G60 Block Dichtsatz G60 Block Sealing Kit
High quality repair Kit for all G60. All parts you need to seal your G60 block. Made in germany.
109.95€ *
G60 6PK Riemen KURZ für Klima G60 Shorter belt 6PK with AC
Shorter belt for smaller pullies like 68mm. Putting a smaller pully you have to shorten the belt to keep preload on your charger! For 72,70 or 68mm pullies. For all G60 WITH Aircondition!
29.95€ *
G60 Umlenkrolle G60 tensiator for 6PK belt
1 New tensiator for the 6PK belt for all G60. On each engine there are 2 of this tensiators.
39.95€ *
G60 Wasserflansch Zylinderkopf seitlich G60 Wateroutlet side cylinderhead
Water flange from Cylinderhead with new O-Ring. This water outlet gets unseal very often due to cracks in the flange. Please use Silicon to seal such as our Dirko HT paste.
9.95€ *
G60 Auslassbogen Dichtplatte BAR-TEK® G60 Gasket for outlet-pipe BAR-TEK®
Gasket for outlet pipe G60 Lader big intercooler. Also for Rally Golf intercooler. Non rosting steel. 100% same design compared to VW.
39.95€ *
G60 Wasserflansch Zylinderkopf vorne G60 Wateroutlet front cylinderhead
Water flange from Cylinderhead with new O-Ring for all G60 engines. This water outlet gets unseal very often due to cracks in the flange. Please use Silicon to seal such as our Dirko HT paste. (Without sensors. Pic shows different flange)
19.95€ *
1 From 2

Valves for turbochargers and naturally aspirated engines

In our wide range of valves and valve train accessories, you will find the right part for every engine. Our SCHRICK blank valves can be customized, for example, for each head. For the inlet, we recommend steel blanks; for the outlet, you should use blanks made of NIMONIC® steel. They are also suitable for turbo engines, since they are extremely heat-resistant.

FERREA offers top-notch valves, including for turbocharged engines, that support a significant performance increase. They feature high temperature resistance and great tensile strength, are made of special heat-treated material and boast premium-quality processing. This is why FERREA is also used in Formula 1 racing and other race series.

Turbo tuning can no longer be imagined, either, without BAR-TEK valves. The valves with the Nimonic super alloy withstand the most grueling temperatures. You´ll definitely notice the boost of your valve train.

Valve springs, valve spring retainers and valve guides

When installing a sports camshaft, you should always use reinforced valve springs. They prevent the collapse of the series springs and improve the closing of the valves, which significantly augments the valve train. Our sports valve springs from Supertech are available with spring plates made of titanium, for instance, which relieve the valve train. They also have a better and quicker response than the series parts.

The BAR-TEK valve guides provide for a better air flow in the channel of the cylinder head. If you install new valves, you should always also renew the valve guides. And if the old guides show very high wear, you should replace them as well. Then check the valve seat and adapt it, if necessary.

Do you need help?

Tell us if you have a part missing or you need help. With 15 years of Motorsport experience, BAR-TEK is the best contact point in the field of car racing and tuning.

Just pay
Logo Vorkasse SLogo ofort Überweisung Logo Paypal Logo Mastercard Logo VISA Logo Maestro Logo VISA electron Logo Postepay Logo Servired Logo Carte Bleue Logo iDEAL Ratenkauf by easyCredit
100 % safe shopping
Seal TÜV seal SSL 20 Years BAR-TEK® Motorsport
15 years of motorsport experience
© BAR-TEK® Motorsport GmbH - All Rights Reserved
All prices incl. VAT. and excl. Shipping