Wastegates – outstanding boost control for turbochargers

Boost control by means of a wastegate prevents unused energy from escaping and stops the speed of your turbocharger from rocketing through the ceiling. With us, you get wastegates by TiAL for turbochargers up to approximately 600 hp. Also included are water-cooled wastegates. Tell us if you have any questions about the right valve. With over 15 years of Motorsport experience, BAR-TEK is the best point of contact in matters of car racing.

Boost control by means of a wastegate prevents unused energy from escaping and stops the speed of your turbocharger from rocketing through the ceiling. With us, you get wastegates by TiAL for... read more »
Close window
Wastegates – outstanding boost control for turbochargers

Boost control by means of a wastegate prevents unused energy from escaping and stops the speed of your turbocharger from rocketing through the ceiling. With us, you get wastegates by TiAL for turbochargers up to approximately 600 hp. Also included are water-cooled wastegates. Tell us if you have any questions about the right valve. With over 15 years of Motorsport experience, BAR-TEK is the best point of contact in matters of car racing.

Close filters
 
  •  
  •  
from to
TiAL Sport MVR Wastegate Membrane TiAL Sport MVR Wastegate Membrane
For 44mm TiAL MVR Wastegates Sometimes it happens that a Wastegate membrane is damaged or torn, for example due to excessive temperature loads. Here is a relatively easy exchange possible. New and original as a replacement
59.95€ *
TiAL Sport MVR Wastegate Diaphragm TiAL Sport MVR Wastegate Diaphragm
For 44mm TiAL MVR Wastegates Sometimes it happens that a Wastegate membrane is damaged or torn, for example due to excessive temperature loads. Here is a relatively easy exchange possible. New and original as a replacement
64.95€ *
Tial MV-R 44mm externes Wastegate wassergekühlt Tial MV-R 44mm external Wastegate water cooled
"TIAL MV-R external Wastegate for Turbo engines on a low cost basis made in USA. Suitable for engines up to 600hp. Watercooled version with Dash 4 connections. Water cooling ports that cycle a small amount of coolant through the actuator...
449.95€ *
Tial 38mm externes Wastegate (F38) Tial 38mm external Wastegate (F38)
"TIAL F38 external Wastegate for Turbo engines on a low cost basis made in USA. Suitable for engines up to 500hp. 347 Stainless Steel Alloy is used for valve and valve housing. High temperature silicone Nomex reinforced actuator...
From 299.95€ *
Tial MV-S 38mm externes Wastegate wassergekühlt Tial MV-S 38mm external Wastegate water cooled
"TIAL MV-S external Wastegate for Turbo engines on a low cost basis made in USA. Suitable for engines up to 600hp. Watercooled version with Dash 4 connections. Water cooling ports that cycle a small amount of coolant through the actuator...
318.96€ *
1.8T Vacuumanschluss Intergrated 1.8T Micro Vacuum Manifold
1.8T Micro Vacuum Manifold The Integrated Engineering micro vacuum manifold provides a sleek and cost effective solution to plumb your components requiring a vacuum source into your intake manifold. This simple fitting provides all of...
49.95€ *
Tial 41mm externes Wastegate (F41) Tial 41mm external Wastegate (F41)
"TIAL F41 external Wastegate for Turbo engines on a low cost basis made in USA. Suitable for engines up to 600hp. 347 Stainless Steel Alloy is used for valve and valve housing. High temperature silicone Nomex reinforced actuator...
From 399.95€ *

Pressure regulators at high speeds

Wastegates are a great support for turbochargers. Because, at high speeds, your engine hits its thermal and mechanical limits quickly. Things get particularly critical should these limits be exceeded. The wastegate, also called bypass valve, opens if a certain boost is reached and then directs exhaust gas directly to the exhaust pipe, i.e. past the turbine. At low speeds, the valve closes and the entire exhaust gas drives the turbine and the compressor again.

TiAL wastegates for highest tuning requirements

Since a wastegate is positioned in the exhaust stream, it is exposed to permanent heat and correspondingly much stress and wear. This is why we rely on wastegates by TiAL, which are of a very high quality and heat-resistant. TiAL housings and valves are made of stainless steel, the inner membrane of flame-resistant and heat-resistant Nomex®, which is additionally reinforced. The spring is also made of stainless steel, which guarantees a constant spring rate across the entire temperature range. From a spring rate of 1.0 bar, dual springs must be used. Our wastegates are suitable for engines of up to approx. 600 hp.- External wastegates with water cooling meet the highest tuning requirements, especially when it comes to car racing. The charge air is water-cooled, enabling you to achieve even more power. In addition, the wastegates are available in different colors including silver, black, purple, blue and red.

Are you overwhelmed?

We like to share our knowledge with other engine tuning freaks. Call us if you need our help or a few tips!

Viewed
Just pay
Logo Vorkasse Logo Klarna (Ex SOFORT Logo Paypal Logo Mastercard Logo VISA Logo Maestro Logo VISA electron Logo Postepay Logo Servired Logo Carte Bleue Logo iDEAL Ratenkauf by easyCredit
100 % safe shopping
Seal TÜV seal SSL 20 Years BAR-TEK® Motorsport
15 years of motorsport experience
© BAR-TEK® Motorsport GmbH - All Rights Reserved
All prices incl. VAT. and excl. Shipping